Fireplace restoration in Galloway, New Jersey brings a spalling, smoking, or sealed-off fireplace back to safe working order. We rebuild fireboxes with firebrick and refractory mortar, reline flues, and repair dampers and crowns. Whether you own a 1920s brick house near Leeds Point or a 1990s colonial off Jimmie Leeds Road, we make the hearth usable again.
Fireplace restoration in Galloway, New Jersey is the trade of rebuilding the firebox, flue, damper, and surrounding masonry so a fireplace burns safely again. We pull out cracked firebrick, grind out failed mortar joints, and set new brick with refractory mortar rated for high heat. If the clay flue tile is cracked or the smoke chamber is rough, we install a stainless steel liner sized to the appliance. A fireplace remodel Galloway NJ homeowners ask for often adds a new damper, chimney cap, and waterproofing sealant on the crown and brick.
Most Galloway calls start the same way: a homeowner opens the damper, smells creosote, and sees a cracked firebox wall. Salt air off Nacote Creek and Oceanville eats mortar and flashing, and the freeze-thaw cycles around Smithville and Pomona spall brick faces. If you search for fireplace restoration near me in Galloway, you want someone who reads the whole chimney, not just the hearth. We inspect with a camera, document the damage, and quote the repair before we start.
Every restoration starts with a camera inspection and a written scope. The core work covers the firebox, flue, damper, crown, and flashing. Optional add-ons like a full fireplace remodel, new surround, or hearth extension are quoted separately so you can see exactly what each piece costs.
We run an inspection camera down the flue and photograph the firebox, smoke chamber, damper, crown, and flashing. You get a written report with the defects marked and a fixed price for the repair.
Cracked firebrick is cut out and replaced with new brick set in refractory mortar. We strike the joints with a tuckpointing trowel and mortar hawk so the firebox looks original when finished.
If the clay flue tile is cracked or deteriorated, we install an insulated stainless steel liner sized to the fireplace opening. The liner is sealed at the top and bottom and rated for the appliance you burn.
We repair or replace the damper, fit a damper clamp where code requires one, and install a chimney cap to keep rain and animals out. Both are included in a standard restoration scope.
We rebuild the crown with chimney crown mix, reset or replace flashing, and apply a breathable waterproofing sealant to the brick. This is the step that stops the water damage that caused much of the masonry failure.
We run an inspection camera down the flue and check the firebox, smoke chamber, damper, crown, and flashing. You get photos of every defect and a written scope with a fixed price. The inspection takes 45 to 60 minutes on a typical Galloway masonry chimney.
Before any masonry work, we sweep the flue with a chimney brush and rods and remove creosote buildup. Gloves, drop cloths, and a HEPA vacuum keep soot out of your living room. We protect the hearth and floor, then stage tools and materials on the truck.
We cut out cracked firebrick with an angle grinder and masonry chisel, then reset new brick with refractory mortar. Joints are struck with a tuckpointing trowel and mortar hawk for a clean finish. A typical firebox rebuild takes one to two days depending on how many courses are damaged.
If the clay flue tile is cracked, we install an insulated stainless steel liner sized to the fireplace opening. We replace or adjust the damper and fit a damper clamp where code requires it. Liner installs run four to six hours on a straight flue.
We repair the crown with chimney crown mix, reset flashing, install a chimney cap, and seal the brick. Then we build a small test fire and watch the draft, checking for smoke backdraft. You get a walkthrough of what we did and a maintenance schedule before we pack up.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
We run a camera down the flue to see cracked clay flue tile, gaps at the liner joints, and creosote buildup that is invisible from the firebox.
Used to sweep creosote and soot from the flue before any masonry repair. A clean flue lets us see the true condition of the liner.
We cut out cracked firebrick and failed mortar joints cleanly so new brick and mortar bond to sound masonry instead of crumbling edges.
Used to pack and strike new mortar joints in the firebox and on the chimney exterior. The finish matches the original joint profile.
Fitted where code requires a damper to stay partially open on vented gas logs. It prevents carbon monoxide from backing into the room.
We use ChimneySaver waterproofing sealant and HomeSaver stainless steel liners because they hold up to Galloway salt air and freeze-thaw cycles.
For factory-built and metal chimney repairs we use Selkirk and DuraVent caps, sections, and adapters that match the original system.
The firebox had three cracked courses of firebrick, failing mortar joints, and a rusted damper that would not close. Smoke rolled into the room on every burn, and the homeowner had stopped using the fireplace two winters earlier.
We rebuilt the firebox with new firebrick and refractory mortar, replaced the damper, and relined the flue with an insulated stainless steel liner. Draft tested clean with no smoke spillage, and the fireplace has burned through two full seasons since.
Water stains spread across the ceiling next to the chimney after every storm. The crown had a hairline crack running the full width, the flashing was lifted at the back, and several brick faces had spalled.
We rebuilt the crown with chimney crown mix, reset the flashing, replaced the cap, and sealed the brick with waterproofing sealant. The next two storms produced no new stains, and the ceiling was patched and painted.
The homeowner wanted a usable fireplace and a cleaner look but did not want to lose the original brick arch. The firebox was sound but the damper was stuck, the cap was missing, and the surround was dated.
We restored the firebox, installed a new damper and stainless cap, and matched the mortar color on the repaired joints. The original arch and mantel stayed in place, and the cosmetic surround was updated in a second visit.
Most fireplace failures trace back to water, heat, or creosote. We diagnose which one caused the damage and fix the source, not just the symptom.
Ask a pro →We cut out the damaged brick with an angle grinder and masonry chisel, then rebuild the firebox with new firebrick and refractory mortar. Joints are struck clean and the firebox is tested with a small fire before we leave.
We check the flue size, smoke chamber, and damper, then correct the cause. That might mean a new damper, a smoke chamber parge, or a correctly sized stainless steel liner. We test the draft with a real fire before finishing.
We trace the leak with a water test, then repair the crown with chimney crown mix, reset flashing, and seal the brick with waterproofing sealant. Repaired sections are matched to the original brick and mortar.
We repair or replace the damper and fit a damper clamp where code requires one. You get a damper that seals tight and opens smoothly, which cuts heat loss between burns.
Typical 2026 pricing in Galloway runs $450 to $1,200 for a firebox rebuild, $1,800 to $4,500 for a stainless steel liner install, and $2,400 to $6,800 for a full restoration with crown, cap, and flashing work. Cost depends on how many courses of firebrick are damaged, flue height, and whether the crown needs a full rebuild. We quote a fixed price after the inspection.
We do. Thrive Sharp handles both restoration and fireplace remodeling Galloway, from rebuilding the firebox to adding a new damper, cap, and surround. We are licensed, insured, and CSIA Certified, and we work on masonry and factory-built fireplaces. Call (844) 803-5147 and we will schedule an inspection, usually within a few days.
Yes. Most pre-1950 fireplaces in Galloway can be restored rather than replaced. We cut out cracked firebrick, rebuild with refractory mortar, reline the flue with a stainless steel liner, and repair the crown and flashing. The original brick arch and mantel stay in place. Only a structurally unsound chimney with failed footings needs a full rebuild.
A firebox rebuild takes one to two days. A flue liner install runs four to six hours. A full restoration with masonry repair, crown work, and a new cap takes three to five days. We schedule around your use of the fireplace and can often complete the work before the first cold snap in October.
Chimney Repair Near MeWhen your chimney needs more than the firebox, we repair crowns, flashing, and masonry in the same visit. Galloway homeowners get one crew for the whole chimney instead of juggling two contractors.Explore →
Chimney Masonry RepairSpalling brick and crumbling mortar around the firebox get rebuilt with matched brick and mortar. We grind out failed joints and tuckpoint them so the repair blends with the original wall.Explore →
Chimney Crown RepairA cracked crown lets water straight into the flue. We rebuild it with chimney crown mix and seal it, which protects the restoration work below from the next storm.Explore →
Chimney ReliningCracked clay flue tile is the most common reason a restored fireplace still smokes. We install an insulated stainless steel liner sized to the firebox opening and appliance.Explore →
Chimney Cap RepairA damaged cap lets rain, birds, and squirrels into the flue. We repair or replace caps with stainless or copper models that fit the chimney and keep animals out.Explore →
Chimney MaintenanceAnnual sweeps and inspections keep a restored fireplace running safely. We remove creosote buildup, check the damper, and catch small masonry issues before they spread.Explore →
Fireplace RepairDamper malfunction, cracked firebrick, and smoke backdraft are all fireplace repair items. We diagnose the cause and fix it, often in a single visit.Explore →
Emergency Chimney RepairSmoke in the house or a chimney leak during a storm gets a same-day response in most of Galloway. We stabilize the chimney and schedule the permanent repair.Explore →One inspection tells you exactly what your fireplace needs and what it costs. We are licensed, insured, and CSIA Certified, and we quote a fixed price before any work starts. Call (844) 803-5147 to schedule your fireplace restoration in Galloway, New Jersey.
Schedule Inspection (844) 803-5147 →Call (844) 803-5147 or send us a message and we will get back to you the same business day. We book Monday through Friday, 8 a.m. to 6 p.m., with same-day and after-hours slots for active leaks and storm damage. Tell us what you are seeing and we will tell you what it takes to fix it.