Smoke rolling into the room on every burn
We measure the flue, check the damper and damper clamp, and match the liner to the appliance. If the chimney is short, we extend the vent to code. The test burn confirms the fix before we leave.
Wood, gas, and insert installs done to NFPA 211 spec
Fireplace installation in Galloway, New Jersey built to burn clean
If you want a fireplace installation in Galloway, New Jersey that passes inspection the first time, we handle the whole job: firebox, flue, liner, venting, and finish. We install wood-burning units, gas inserts, and high-efficiency fireplace insert installation in Galloway NJ for homeowners in Smithville, Pomona, and across Galloway Township. Fall is booking fast, so call early.
Careful work. Honest options.
About this service
What fireplace installation in Galloway, New Jersey involves
Fireplace installation in Galloway, New Jersey is the process of setting a new firebox, running a code-compliant flue or stainless steel liner, and tying the unit into your home's venting so it drafts correctly and holds up to heat. It is not a drop-in job. We check the existing chimney, size the flue to the appliance, pour a chimney crown mix where needed, and set firebrick with refractory mortar. Every joint gets checked against NFPA 211 before we call it done.
Most Galloway homeowners call us for one of three reasons: an old masonry fireplace that smokes back into the room, a remodel that needs a modern insert, or a new build with no fireplace at all. Coastal humidity here works on mortar joints and flashing year-round, so we inspect for spalling brick and chimney leaks before we set anything. If you have been searching fireplace installation near me in Galloway, that pre-install inspection is the part most crews skip.
- ✓ Heat that stays in the room
- ✓ Drafting that works
- ✓ Code-correct from day one
- ✓ Lower creosote risk
What's included
What our fireplace installation includes
Every install starts with a full chimney inspection and ends with a test burn. These are the core pieces we handle. If your chimney needs relining, crown work, or masonry repair first, we quote that separately and clearly before we start.
✓
Full chimney inspection
We run an inspection camera down the flue and check the firebox, damper, crown, flashing, and brick condition. You get photos and a written summary. This is where we catch the problems that would otherwise show up after the appliance is set.
✓
Flue sizing and liner
We size the stainless steel liner to the appliance, not the other way around. An undersized flue causes smoke backdraft and creosote buildup. Correct sizing is the single biggest factor in how well your new fireplace performs.
✓
Firebox and firebrick set
Firebrick gets laid with refractory mortar rated for high heat. We check every joint and clearance to combustibles against NFPA 211. This is the part that keeps the fire where it belongs.
✓
Venting and termination
We install the vent run and cap using DuraVent, Selkirk, or manufacturer-specified components. Vent height and termination get set to code so the fireplace drafts correctly regardless of wind direction.
✓
Test burn and handoff
We light a test fire, watch the draft, and check for spillage at the face. Then we walk you through operation, damper use, and the first-season burn-in. You leave knowing exactly how to run the unit.
How it works
How our fireplace installation process runs
01
Inspection first
We run an inspection camera down the flue and check the firebox, damper, crown, and flashing. You get photos of what we found. If the chimney needs relining or crown work before a new unit goes in, you hear it now, not after the appliance is set. This visit takes 45 to 60 minutes.
02
Sizing and quote
We match the appliance to the flue, confirm clearances to combustibles, and price the job. You see the liner spec, the venting, and the labor broken out. No surprises mid-job. Most quotes go out the same day as the inspection.
03
Prep and protection
Floors get covered, and we set up containment so dust stays in the work zone. If we are cutting brick, we use an angle grinder with a shroud and a masonry chisel for the fine work. Your furniture and floors stay clean.
04
Install and vent
We set the firebox, lay firebrick with refractory mortar, and drop the stainless steel liner or vent run. DuraVent and Selkirk components go in per manufacturer spec. A typical liner run takes four to six hours; a full masonry firebox rebuild runs longer.
05
Test burn and walkthrough
We light a test fire, watch the draft, and check for smoke spillage at the face. Then we walk you through operation, damper use, and the first-season burn-in. You get the install documented and a maintenance schedule before we pack up.
Tools & methods
Tools and methods we use
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Inspection camera
We run it down the flue to see cracked clay flue tile, creosote buildup, and liner damage that you cannot see from the firebox. Findings get photographed for your records.
Chimney brush and rods
Used to sweep soot and creosote before a liner goes in. A clean flue lets the new liner seat properly and keeps the first burn clean.
Angle grinder and masonry chisel
For cutting brick and cleaning up firebox openings during install. We use a shroud to control dust and keep the work zone contained.
Tuckpointing trowel and mortar hawk
For repointing mortar joints and setting firebrick with refractory mortar. Clean joints are what keep water out and the stack strong.
DuraVent and Selkirk venting
Manufacturer-specified venting components for gas and wood appliances. We match the vent system to the unit so clearances and performance meet spec.
ChimneySaver waterproofing
A breathable sealant applied to masonry after install. It blocks rain and salt air while letting the brick dry, which slows spalling and mortar joint deterioration.
Real results
Before and after.
Smoking masonry fireplace in Smithville
Before
A 1970s masonry fireplace that smoked into the room on every burn. The flue had cracked clay flue tile and heavy creosote buildup, and the damper was rusted shut. The homeowner had stopped using it entirely.
After
We swept the flue, installed an insulated stainless steel liner, replaced the damper, and set a sealed wood insert. The test burn drafted clean with no spillage. Heat output went from almost nothing to 65 percent of the burn going into the room.
Gas insert install in Pomona
Before
A homeowner with an oversized open masonry flue that would not draft a modern gas insert. The chimney crown had a hairline crack and the flashing was lifting at the roofline, letting water into the firebox.
After
We repaired the crown with chimney crown mix, reset the flashing, and installed a correctly sized stainless liner with a direct-vent gas insert. The install took one day. The firebox is dry and the insert lights on the first try.
New build fireplace near Jimmie Leeds Road
Before
New construction with framing in place and no fireplace or flue. The builder needed clearances documented for the final inspection and the homeowner wanted a wood-burning unit with a real masonry look.
After
We set the firebox with firebrick and refractory mortar, ran the vent to code, and confirmed clearances to combustibles against NFPA 211 and IBC. The install passed inspection on the first look. Hearth dimensions were documented for the file.
Problems we solve
Problems we solve with affordable fireplace installation Galloway
Most fireplace calls trace back to one of a few failures. Here is what we see in Galloway and how we fix it.
Ask a pro →↗
Cracked clay flue tile behind the firebox
We reline with an insulated stainless steel liner sized to the new unit. The old clay flue tile stays in place as a chase, and the new liner carries the heat safely. Most relines take four to six hours.
Water stains and rust around the firebox
We trace the leak, repair the flashing, pour a new chimney crown mix where needed, and seal the masonry with a breathable waterproofing sealant. Then we install the fireplace on a dry, sound chimney.
An old open fireplace that heats nothing
We install a sealed insert with a correctly sized liner. That flips the efficiency to 60 to 70 percent of the burn going into the room. Most Galloway insert jobs finish in one day.
Proof you can check
Licensed, certified, and local
✓
CSIA Certified Chimney SweepChimney Safety Institute of America
✓
NFI CertifiedNational Fireplace Institute
✓
NCSG MemberNational Chimney Sweep Guild
✓
New Jersey Home Improvement Contractor (HIC) LicenseNew Jersey Division of Consumer Affairs
✓
OSHA 10Occupational Safety and Health Administration
Most fireplace installs in Galloway run $2,800 to $7,500 in 2026, depending on the unit and whether a new liner is needed. A gas insert with a stainless steel liner typically lands $3,200 to $5,500 installed. Full masonry firebox builds run higher. Fireplace insert installation cost Galloway New Jersey varies most with flue height and liner length, so we quote after measuring.
We do. Thrive Sharp installs inserts across Galloway Township, Smithville, Pomona, and the surrounding areas. We handle the liner, the surround, the venting, and the test burn, and we work to NFI Certified and NFPA 211 standards. Call (844) 803-5147 and we will schedule an inspection so you get an exact quote, not a phone estimate.
You can install wood-burning, gas, pellet, or electric units, and each has different venting rules. Wood and gas need a properly sized flue or stainless steel liner; direct-vent gas can go through a wall. We check your existing chimney, clearances, and local code before recommending a type, so you do not buy a unit your flue cannot handle.
A gas or wood insert usually takes one day, roughly six to eight hours on site. A full masonry fireplace build or a job that needs chimney relining first runs two to three days. We confirm the schedule at quote time and keep you posted if anything changes. Most Galloway installs are done before the first hard freeze.
More services
Related Services
Chimney Repair Near MeIf your existing chimney has cracked brick or a failing crown, we repair it before or alongside a new fireplace install. Fixing the structure first keeps the new unit drafting right and protects the warranty on the appliance.Explore →
Chimney Masonry RepairSpalling brick and deteriorated mortar joints are common on older Galloway chimneys. We repoint and rebuild masonry so the stack is solid enough to carry a new liner and handle the heat load of a modern fireplace.Explore →
Chimney Crown RepairA cracked crown lets water into the flue, which ruins liners and rusts dampers. We pour a new chimney crown mix and seal it before installation so your new fireplace is not sitting on top of a leaking chimney.Explore →
Chimney ReliningMost new wood and gas appliances need a correctly sized stainless steel liner. We install insulated liners sized to the unit, which improves draft and cuts creosote buildup from the first season.Explore →
Chimney Cap RepairA missing or damaged cap lets rain, birds, and squirrels into the flue. We repair or replace caps with stainless models before install so debris never lands on a brand-new damper or liner.Explore →
Chimney MaintenanceAnnual service keeps a new fireplace running clean. We sweep, inspect the liner, check the damper, and look at flashing and crown condition each year, usually in late summer before the burning season starts.Explore →
Fireplace RepairIf your current fireplace smokes, leaks, or will not hold a fire, we diagnose the damper, firebox, and flue. Sometimes a repair beats a replacement, and we tell you which one you actually need.Explore →
Emergency Chimney RepairChimney fires, sudden leaks, and collapsed crowns do not wait for business hours. We respond to urgent calls around Galloway and stabilize the chimney so your home stays safe until full repairs can be scheduled.Explore → Ready when you are
Get your fireplace installation in Galloway, New Jersey scheduled
Fall slots fill quickly, and we would rather install your fireplace before the first freeze than after. Call (844) 803-5147 and we will set up the inspection, quote the job, and give you a start date. Licensed, insured, and code-correct from the first burn.
Book Inspection (844) 803-5147 →
Request an appointment
Get your chimney looked at
Call (844) 803-5147 or send us a message and we will get back to you the same business day. We book Monday through Friday, 8 a.m. to 6 p.m., with same-day and after-hours slots for active leaks and storm damage. Tell us what you are seeing and we will tell you what it takes to fix it.
Call anytime(844) 803-5147Email the officeinfo@thrivesharp.shop
Office hoursOpen 24 hours · 7 days a week